www中文字幕-wwxx全免费视频-ww久久-ww毛片-ww欧美-ww亚洲ww亚在线观看

Your Position: Home > News > Industry News

Common Faults of Gear Oil Pump of Quenching Oil Filter

2019/8/1??????view:

  Quenching oil is classified as ordinary quenching oil, high speed quenching oil, bright quenching oil and vacuum quenching oil.

  1. Ordinary quenching oil generally uses various mineral oils (such as oil for total loss system) as quenching medium. The greatest advantage of oil as quenching medium is that compared with water, it can enter the convection phase with slower cooling rate at higher temperature during quenching and cooling process, which is beneficial to reduce the tendency of quenching deformation and cracking of workpiece.

  The disadvantages of common quenching oil are as follows:

  (1) The cooling capacity of oil is much smaller than that of water, especially in the temperature range (500 650 C), which is the most unstable nose tip region of supercooled austenite. Therefore, stirring is often used to increase cooling capacity, but sometimes it also increases the degree of workpiece deformation.

  (2) As a quenching medium, mineral oil requires high flash point. Otherwise, the danger of fire in use is greater and the safety is poor.

  (3) Oil fume pollution of the environment.

  (4) Quenching oil (including various new types of quenching oil) will deteriorate after long-term use and its cooling capacity will decrease, thus affecting the quenching quality of the workpiece. Such as: hardening, hardening, soft spots and so on. Common quenching oil is only suitable for quenching various alloy steels with high stability and good hardenability of supercooled austenite and carbon steel workpieces with cross section less than 5 mm.

  2. High-speed quenching oil refers to those quenching oils whose cooling rate is increased in the high temperature zone. There are two basic ways to obtain high speed quenching oil:

  (1) Reasonable selection of mineral oils with different types and viscosities, and appropriate mixing ratio to obtain high-speed quenching oil.

  (2) High-speed quenching oil is obtained by adding additives to ordinary quenching oil.

  High-speed quenching oil is suitable for large cross-section carbon steel or low-alloy workpieces. The temperature is 20-80 C. It is not easy to be too high to prevent accelerated aging. Water is forbidden to infiltrate into the oil to avoid affecting the cooling effect.

  3. Bright quenching oil is a kind of quenching oil which can keep the surface of quenched workpiece bright under controlled atmosphere. It is prepared by adding different polymer additives (such as brighteners, antioxidants, etc.) into mineral oil. The service temperature of the brightening quenching oil is 20-80 C. It is strictly forbidden to mix water and other oils in oil.

  Bright quenching oil is suitable for quenching and cooling of steel parts heated in controlled atmosphere.

  4. Vacuum quenching oil is prepared by vacuum distillation and vacuum degassing of ordinary quenching oil, followed by refrigerant, brightness and antioxidant.

  It is suitable for quenching and cooling of bearing steel, die steel, structural steel and alloy carburized steel.

  The filtering forms of quenching oil are mainly divided into portable filters, pressure filters, vacuum filters, centrifugal filters and so on.

  Quenching oil gear oil pump is suitable for conveying various lubricating liquids. The temperature is not higher than 70 C. If the temperature is 200 C, the high temperature resistant material can be used. This pump is not suitable for conveying corrosive, hard particles or fibers, highly volatile or low flash point liquids, such as gasoline, benzene, etc.

  Common faults of gear oil pump on quenching oil filter:

  What are the common faults and maintenance methods of circular arc gear oil pump as follows:

  (1) Fault Phenomenon of Circular Arc Gear Oil Pump: Pump Can't Layout Material

  Arc gear oil pump failure reasons: a, reverse rotation direction; b, inhalation or discharge valve closed; c, low inlet material or pressure; d, too high viscosity, pump can not bite material arc gear oil pump countermeasures: a, confirm the direction of rotation; b, confirm whether the valve is closed; c, check the valve and pressure gauge; d, check liquid viscosity, in order to low speed. Whether or not the flow rate proportionate to the rotational speed occurs during operation, and if there is flow rate, the inflow will be insufficient.

  (2) Fault Phenomenon of Circular Arc Gear Oil Pump: Insufficient Pump Flow

  Causes of failure of circular arc gear oil pump: A. closure of suction or discharge valve; B. low inlet pressure; C. blockage of outlet pipeline; D. leakage of packing box; E. low speed

  Arc gear oil pump countermeasures: a, confirm whether the valve is closed; b, check whether the valve is open; c, confirm whether the discharge is normal; d, tightening; a large number of leakage affect production, should stop operation, disassembly and inspection; e, check the actual speed of the pump shaft;

  Operation and maintenance method of circular arc gear oil pump:

  (1) Check the sealing of all pipe flanges and joints before start-up.

  (2) Disk coupling, no friction and collision sound.

  (3) The first start-up shall inject the conveying liquid into the pump.

  (4) Before starting, all the valves in the suction and discharge pipelines should be opened, and the start of the closed valves should be strictly prohibited.

  (5) Start the motor after verifying the direction of rotation.


主站蜘蛛池模板: 久久99网 | 久久久久久国产精品免费 | 性欧美长视频免费观看不卡 | 伊人久久综在合线亚洲91 | 中文字幕一区二区日产乱码 | 欧美一区二区三区在线视频 | 国产亚洲精品日韩香蕉网 | 日本三级带日本三级带黄首页 | 在线不卡免费视频 | 91亚洲精品 | 国产精品99一区二区三区 | 在线91精品国产免费 | 欧美激情网址 | 99精品国产久热在线观看66 | 性孕妇video国产中国 | 午夜影院男女 | 成人一区二区免费中文字幕 | 日韩精品一区在线观看 | 久草在线免费福利资源 | 欧美国产精品亚洲精品第一区 | 亚洲精品一二三四区 | 欧美一区二区三区免费观看视频 | 天天操天天干天天干 | 精品一成人岛国片在线观看 | 精品成人 | 高清人人天天夜夜曰狠狠狠狠 | 久久人人插 | 久久综合久久自在自线精品自 | 小毛片网站 | 日本xx高清视频免费观看 | 精品一区二区三 | 免费日b视频 | 欧美一级刺激毛片 | 国产成人在线免费观看 | 91久久国产综合精品 | 草视频在线观看 | a在线观看免费视频 | 亚洲欧美高清视频 | 色拍拍噜噜噜在线视频 | 久久只有精品视频 | 一本久道久久综合婷婷五 |